UKAEA Journals

Showing 1 - 10 of 26 Journals Results
2018
UKAEA-CCFE-PR(20)64

The JET outboard divertor targets are the in-vessel components which receive the largest heat flux density. Surface delamination, radial cracks, and tie rod failures have been observed in the outboard tungsten-coated CFC tiles, while bulk tungsten special lamellas were intentionally melted in dedicated experiments. These different types of damag…

Preprint
2019
UKAEA-CCFE-PR(19)62

The pedestal structure, ELM losses and linear MHD stability are analysed in a series of JET-ILW H and D type I ELMy H-mode plasmas. The pedestal pressure (pPED) is typically higher in D than in H at the same input power, with the difference mainly due to lower density in H than in D. At the same input power, the pedestal electron pressur…

Preprint
2017
CCFE-PR(17)75

This paper presents the use of a novel modelling technique based around intermittent transport due to filament motion, to interpret experimental profile and fluctuation data in the scrape-off layer (SOL) of JET during the onset and evolution of a density profile shoulder. Three cases are studied at different points in a density ramp experiment wher…

Preprint Published
2017
CCFE-PR(17)03

Statistical analysis of the ion flux to the JET outer-wall is conducted in outer-wall limiter mounted Langmuir probe (OLP) time-series across a wide range of plasma current and line-averaged density during Ohmically heated horizontal target L-mode plasmas. The mean, _, and the standard deviation, _, of the ion-saturation current measured by the OLP…

Preprint Published
2016
CCFE-PR(16)78

The dynamics and stability of divertor detachment in N2 seeded, type-I, ELMy H-mode plasmas with dominant NBI heating in the JET-ILW device is studied by means of an integrated analysis of diagnostic data from several systems, classifying data relative to the ELM times. It is thereby possible to study the response of the detachment evolution to the…

Preprint Published
2016
CCFE-PR(16)24

Rotating collectors and quartz microbalances (QMBs) are used in JET to provide time-dependent measurements of erosion and deposition. Rotation of collector discs behind apertures allows recording of the long term evolution of deposition. QMBs measure mass change via the frequency deviations of vibrating quartz crystals. These diagnostics are used t…

Preprint Published
2016
CCFE-PR(16)23

JET components are removed periodically for surface analysis to assess material migration and fuel retention. This paper describes issues related to handling JET components and procedures for preparing samples for analysis; in particular a newly developed procedure for cutting beryllium tiles is presented. Consideration is also given to the hazards…

Preprint Published
2016
CCFE-PR(16)81

Recent improvements in software tools and methodology have allowed us to perform a more comprehensive in-vessel calibration for all mid-infrared camera systems at JET. A comparison of experimental methods to calculate the non-uniformity correction is described as well as the linearity for the different camera systems. Measurements of the temperatur…

Preprint Published
2015
CCFE-PR(15)32

Results of the first dust survey in JET with the ITER - Like Wall (JET - ILW) are presented. The sampling was performed using adhesive stickers from the divertor tiles where the greatest material deposition was detected after the first JET - ILW campaign in 2011 - 2012. The emphasis was especially on metal particles (Be and W) with the aim to deter…

Preprint Published
2015
CCFE-PR(15)111

Recent studies dedicated to the characterisation of in-vessel dust in JET with the new ITER-like wall (ILW) show that dust levels are orders of magnitude lower compared with the latter stages of the carbon-wall (CW) period and are decreasing with operational time. Less than 1 g of dust was recovered in a recent inspection, compared with more than 2…

Preprint Published