-
UKAEA-CCFE-PR(25)3132025
This study aims to compare the effects of neutron and self-ion irradiation on the mechanical properties and microstructural evolution in W. Neutron irradiation at the HFR reactor to 1.67 dpa at 800 ◦C resulted in the formation of large Re and Os rich clusters and voids. The post-irradiation composition was measured using APT and verfified against…
-
UKAEA-CCFE-PR(24)2682024
Silicon carbide fibre reinforced silicon carbide matrix composite (SiC/SiC) is a key structural material for fusion reactors to allow high temperature operation of liquid lithium breeder blankets. This research investigated the corrosion behaviour of two SiC/SiC composites (using Tyranno SA3 and SA4 fibres) immersed in static liquid lithium at 6…
-
UKAEA-CCFE-PR(24)2402023
In this study, we compare the formation of radiation induced defects in W and W-Re-Os alloys, exposed to an equivalent dose of self-ion and neutron irradiation. Transmutation reactions in the neutron irradiated material are simulated in the ion implanted materials by alloying with representative quantities of Re and Os (1.4 and 0.1 at.% respecti…
-
UKAEA-CCFE-CP(23)422022
A tungsten Langmuir probe exposed in the JET divertor during the ITER-like wall campaigns (ILW) has been studied to evaluate changes in mechanical properties and microstructure. The tip of the probe that was exposed to plasma was cross-sectioned and polished for post mortem analysis. Analysis involved a comparison with a non-exposed probe to de…
-
UKAEA-CCFE-PR(21)272021
Tungsten is one the primary candidate materials for the high neutron flux, high temperature components of a future demonstrate fusion reactor. Despite this, there is a lack of data on W under fusion relevant neutron doses and irradiation temperatures. Transmutation reactions result in the production of Re and Os solute atoms, at a rate which is …
-
UKAEA-CCFE-PR(20)922020
Raman spectroscopy has been used to identify defective bonding in neon and silicon ion irradiated single crystals of 6H-SiC. Observable differences exist in the CC bonding region corresponding to different defect structures for neon and silicon ion implantations. Evidence of oxidation during high temperature ion implantation is observed as C-O a…
-
UKAEA-CCFE-PR(20)912020
Ion implantation is widely used as a surrogate for neutron irradiation in the investigation of radiation damage on the properties of materials. Due to the small depth of damage, micromechanical methods must be used to extract material properties. In this work, nanoindentation has been applied to ion irradiated silicon carbide to extract radiatio…
-
UKAEA-CCFE-PR(20)862020
Focussed ion beam (FIB) milling can be used to reveal sub-surface fracture and deformation below indents in materials. However, evolution of residual stresses around the indent impression cause changes to the crack morphology during the FIB cross-sectioning procedure. Berkovich nanoindents in single crystal hexagonal (6H) silicon carbide cause r…
-
UKAEA-CCFE-PR(19)512019
Only limited data exist on the effect of neutron irradiation on the brittle to ductile transition (BDT) in tungsten. This work investigates the increase in brittle to ductile transition temperature (BDTT) following neutron irradiation to 1.67 displacements per atom, using four-point bend tests over a range of temperatures (623 – 1173 K) and strai…
-
UKAEA-CCFE-PR(19)422019
High temperature, neutron irradiated single crystal tungsten, with a post irradiation composition of W-1.20±0.11at.%Re-0.11±0.05at.%Os-0.03±0.01at.%Ta was characterised using a combination of Atom Probe Tomography (APT) and Scanning Transmission Electron Microscopy (STEM). APT showed that within nanoscale clusters of Re/Os, the atomic density wa…
Showing 1 - 10 of 16 UKAEA Paper Results