-
UKAEA-CCFE-CP(24)092023
The JET ITER-like Wall (ILW) divertor mostly consists of CFC tiles coated with a thick tungsten (W) layer over a molybdenum (Mo) interlayer. Poloidal sets of tiles are additionally coated with ~3 microns of Mo and ~4 microns of W to act as markers to measure the erosion/deposition during ILW campaigns. A few of the marker tiles only have the Mo …
-
UKAEA-CCFE-PR(23)1242023
Beryllium samples from the JET ITER-like wall limiter tiles with either co-deposits or surface cracks caused by melt damage, were immersed into boiling water for 4 h 15 min to simulate and assess the impact of coolant water ingress into a tokamak on the state of Be components. Microscopy of the water-treated surfaces and the residue in the water re…
-
UKAEA-CCFE-CP(23)422022
A tungsten Langmuir probe exposed in the JET divertor during the ITER-like wall campaigns (ILW) has been studied to evaluate changes in mechanical properties and microstructure. The tip of the probe that was exposed to plasma was cross-sectioned and polished for post mortem analysis. Analysis involved a comparison with a non-exposed probe to de…
-
UKAEA-CCFE-PR(22)602022
This work was carried out to identify sources of errors, uncertainties and discrepancies in studies of fuel retention in wall components from the JET tokamak using methods based on thermal desorption. The parallel aim was to establish good practices in measurements and to unify procedures in data handling. A comprehensive program designed for deute…
-
UKAEA-CCFE-CP(21)122021
This contribution outlines a strategy for assessing tritium (T) inventory in plasma facing components (PFC) during JET T operations. It is based on retention as a fraction of fuel injected in-vessel, currently reported as 0.24% for 2011-2012 operating period, in conjunction with the planned T pulse schedule providing fueling of 4 g T injected per d…
-
UKAEA-CCFE-CP(20)742020
Post mortem analysis shows that mid and high atomic number metallic impurities are present in deposits on JET plasma facing components with the highest amount of Ni and W, and therefore the largest sink, being found at the top of the inner divertor. Sources are defined as “continuous” or “specific”, in that “continuous” sources…
-
UKAEA-CCFE-CP(20)842019
JET has now completed three operating periods, ILW1, ILW2 and ILW3, giving an opportunity to make comparisons between tiles exposed for single operating periods and also comparisons of tiles exposed for all three periods, ILW1-3 (2011-2016). In this contribution, a comprehensive overview of fuel retention and material erosion/deposition patterns…
-
CCFE-PR(16)242016
Rotating collectors and quartz microbalances (QMBs) are used in JET to provide time-dependent measurements of erosion and deposition. Rotation of collector discs behind apertures allows recording of the long term evolution of deposition. QMBs measure mass change via the frequency deviations of vibrating quartz crystals. These diagnostics are used t…
-
CCFE-PR(17)352015
The JET tokamak is unique amongst present fusion devices in its capability to operate at high plasma current, providing the closest plasma parameters to ITER. The physics benefits of high current operation have to be balanced against the risks to the integrity of the machine due to high force disruptions. The installation of the ITER-Like Wall (ILW…
-
CCFE-PR(15)252015
A set of Be and W tiles removed after the first ITER-like Wall campaigns (JET-ILW) from 2011-2012 has been analysed. The results indicate that the primary erosion site is in the main chamber (Be) as in previous carbon campaigns (JET-C). In particular the limiters tiles near the mid-plane are eroded probably during the limiter phases of discharges. …
Showing 1 - 10 of 16 UKAEA Paper Results