-
UKAEA-STEP-PR(23)132023
Developments in fusion energy technology and the aspiration to build and run commercial fusion energy power plants has seen the commencement of numerous publicly and privately funded projects in recent years. Megaprojects, like fusion power plants, by their very nature are inherently complex and risky, therefore providing a robust cost estimate in …
-
UKAEA-CCFE-PR(23)1482023
Silicon carbide fibre–reinforced silicon carbide matrix (SiCf/SiC) composites are desirable in structural nuclear applications due to their low density, high temperature strength and tolerance to energetic radiation. We have subjected two industrial grades of SiCf/SiC to high energy He²⁺ ion irradiation, up to 10,000 a…
-
UKAEA-CCFE-PR(23)1242023
Beryllium samples from the JET ITER-like wall limiter tiles with either co-deposits or surface cracks caused by melt damage, were immersed into boiling water for 4 h 15 min to simulate and assess the impact of coolant water ingress into a tokamak on the state of Be components. Microscopy of the water-treated surfaces and the residue in the water re…
-
UKAEA-CCFE-PR(23)1882022
In 2019, the JET-ILW was equipped with a Shattered Pellet Injector (SPI) system with a wide capability to allow studies on the efficacy of shattered pellets in reducing the electro-magnetic and the thermal loads during disruptions and the avoidance/suppression of the formation of runaway electrons. The fully commissioned system became operationa…
-
UKAEA-CCFE-CP(22)072022
Neutron spectrum unfolding using activation foils is currently the primary technique planned for measuring the neutron energy spectrum at the first wall of power-generating fusion reactors. Room for improvement in the effectiveness of current foil selection was identified, and a program produced to select foils procedurally in order to maximise the…
-
UKAEA-CCFE-PR(22)392022
In the absence of official standards and guidelines for nuclear fusion plants, fusion designers adopted, as far as possible, well-established standards for fission-based nuclear power plants (NPPs). This often implies interpretation and/or extrapolation, due to differences in structures, systems and components, materials, safety mitigation systems,…
-
UKAEA-CCFE-PR(23)1042021
MAST pedestal data has been analysed, where a pedestal database of 892 shots was obtained, using the new upgraded MAST Thomson Scattering (TS) diagnostic. Various ELM types are discussed, where characteristics and trends of MAST pedestals are shown. The data from the upgraded TS diagnostic confirms pedestal characteristics found in earlier analy…
-
UKAEA-CCFE-CP(23)142021
The high heat fluxes to the divertor during edge localised mode (ELM) instabilities have to be reduced for a sustainable future tokamak reactor. A solution to reduce the heat fluxes could be the Super-X divertor, this divertor configuration will be tested on MAST-U. ELM simulations for MAST-U Super-X tokamak plasmas have been obtained, using JOR…
-
UKAEA-CCFE-CP(21)082021
The pedestal plays an important role in determining the confinement in tokamak H-mode plasmas. However, the steep pressure gradients in this transport barrier also lead to edge localized modes (ELMs) [1]. There is good understanding of the pedestal in type I ELM regimes [2], however, type I ELMs are known to damage plasma facing components and f…
-
UKAEA-CCFE-CP(21)072021
The disruption mitigation system at ITER will include four shattered pellet injectors (SPI), which will be dedicated to the mitigation of electro-magnetic loads (EML), thermal loads and the avoidance and suppression of runaway electrons. Recently the JETILW was equipped with an SPI with a wide capability. Specifically: pellet diameter d = [4.57, 8.…
Showing 11 - 20 of 61 UKAEA Paper Results