UKAEA Journals

Showing 1 - 10 of 10 Journals Results
2019
UKAEA-CCFE-PR(20)23

To ensure optimal plasma performance at high Qfus for the baseline scenario foreseen for the International Tokamak Experimental Reactor (ITER), fuelling requirements, in particular for non-stationary phases, need to be assessed by means of integrated modelling due to different expected fuelling behaviour and additional challenges that need to be…

Preprint Purchase
The published version of this paper is currently under embargo and will be available on 05/05/2021
2019
UKAEA-CCFE-PR(19)62

The pedestal structure, ELM losses and linear MHD stability are analysed in a series of JET-ILW H and D type I ELMy H-mode plasmas. The pedestal pressure (pPED) is typically higher in D than in H at the same input power, with the difference mainly due to lower density in H than in D. At the same input power, the pedestal electron pressur…

Preprint Purchase
The published version of this paper is currently under embargo and will be available on 09/03/2022
2019
UKAEA-CCFE-PR(19)23

We have modelled self-consistently the most efficient ways to fuel ITER Hydrogen (H), Helium (He) and Deuterium-Tritium (DT) plasmas with gas and/or pellet injection with the integrated core and 2D SOL/divertor suite of codes JINTRAC. As far as we are aware, for ITER this is the first time modelling of the entire plasma has been carried out to foll…

Preprint
2018
UKAEA-CCFE-PR(18)22

The operation of a tokamak designed to test the sustainability of a thermonuclear grade plasma like the International Tokamak Experimental Reactor (ITER) presents several challenges. Among them is the necessity of fuelling the plasma to reach the density required to generate enough fusion power to achieve Q = 10 and, at the same time, to protect th…

Preprint Published
2016

There is experimental evidence that the pedestal dynamics in type-I ELMy H-mode discharges is significantly affected by a change in the recycling conditions at the tungsten plasma-facing components (W-PFCs) after an ELM event. The integrated code JINTRAC has been employed to assess the impact of recycling conditions during type-I ELMs in JET ITER-l…

Published
2015
CCFE-PR(15)29

ITER operations require effective fuelling of the core plasma for conditions in which neutral dynamics through the scrape-off layer (SOL) is expected to affect significantly the efficiency of gas penetration. On the basis of previous analysis for stationary conditions, pellets are foreseen to provide core fuelling of high-Q DT scenarios. In this pa…

Preprint Published
2015
CCFE-PR(15)111

Recent studies dedicated to the characterisation of in-vessel dust in JET with the new ITER-like wall (ILW) show that dust levels are orders of magnitude lower compared with the latter stages of the carbon-wall (CW) period and are decreasing with operational time. Less than 1 g of dust was recovered in a recent inspection, compared with more than 2…

Preprint Published
2015
CCFE-PR(15)26

A discrepancy in the divertor radiated powers between EDGE2D-EIRENE simulations, both with and without drifts, and JET-ILW experiments employing a set of NBI-heated L-mode discharges with step-wise density variation is investigated. Results from a VUV/visible poloidally scanning spectrometer are used together with bolometric measurements to determi…

Preprint Published
2015
CCFE-PR(15)128

The influence of the ITER-like Wall (ILW) with divertor target plate made of tungsten (W), on plasma performance in JET H-mode is being investigated since 2011 (see [1] and references therein). One of the key issues in discharges with low level of D fuelling is observed accumulation of W in the plasma core, which leads to a reduction in plasma perf…

Preprint Published
2015
CCFE-PR(15)115

We present the application of an improved EDGE2D-EIRENE SOL transport model for the ELM phase utilizing kinetic correction of the sheath-heat-transmission coefficients and heat-flux-limiting factors used in fluid SOL modelling. With a statistical analysis over a range of similar Type-I ELMy H-mode discharges performed at the end of the first JET IT…

Preprint Published