-
UKAEA-CCFE-PR(26)4152025
An understanding of the occurrence of opacity is important for modelling the power exhaust of magnetic confinement fusion plasmas. The absorption and reemission of radiation alters the magnitude and distribution of radiation within the divertor of the fusion machines, the plasma volume wi…
-
UKAEA-CCFE-PR(25)3792025
A robust disruption mitigation system (DMS) requires accurate characterization of key disruption timescales, one of the most notable being the thermal quench (TQ). Recent modeling of shattered pellet injection (SPI) into ITER plasmas, using JOREK and INDEX, suggests long TQ durations (6–10 ms) and slow cold front propagation due to the large p…
-
UKAEA-CCFE-PR(26)4532024
Experimental campaigns at the Joint European Torus with an ITER-like Be/W wall (JET-ILW) with pure deuterium (D), tritium (T) and Deuterium-Tritium (DT) were a unique opportunity to explore various aspects related to the ITER operation. It should also be emphasized that the JET campaign at the end of 2021 included the first tokamak experiments u…
-
UKAEA-CCFE-PR(26)4512024
An understanding of the behaviour of the D or He fuel used in tokamak discharges is essential in analyses such as modelling edge and divertor transport and the erosion of the vessel walls. However, poor agreement is found between measurements made on the JET tokamak and collisional-radiative models used …
-
UKAEA-CCFE-CP(25)142024
The typical pulse on the JET tokamak is ~10s during the main phase of the discharge, however long discharge operation (>30s) is possible with sufficient preparation and care. During the last period of JET operation in 2023 long pulses in deuterium plasmas were developed to assess the sustainment of the plasma performance over current resistive t…
-
UKAEA-CCFE-PR(25)2892023
This paper reports the first experiment carried out in deuterium–tritium addressing the integration of a radiative divertor for heat-load control with good confinement. Neon seeding was carried out for the first time in a D–T plasma as part of the second D–T campaign of JET with its Be/W wall environment. The technical difficulties linked to …
-
UKAEA-CCFE-PR(24)2472023
The JET hybrid scenario has been developed from low plasma current carbon wall discharges to the record-breaking Deuterium-Tritium plasmas obtained in 2021 with the ITER-like Be/W wall. The development started in pure Deuterium with refinement of the plasma current, and toroidal magnetic field choices and succeeded in solving the heat load challeng…
-
UKAEA-CCFE-PR(24)2462023
Ion Cyclotron wave (IC) assisted breakdown would be important for reducing risks to plasma initiation during the ITER pre-fusion operation phase under difficult vessel conditions. Hence, studies were performed at JET, at ITER relevant loop electric field — and in a regime, and , where plasma breakdown had not previously been achieved on JE…
-
UKAEA-CCFE-PR(23)1882022
In 2019, the JET-ILW was equipped with a Shattered Pellet Injector (SPI) system with a wide capability to allow studies on the efficacy of shattered pellets in reducing the electro-magnetic and the thermal loads during disruptions and the avoidance/suppression of the formation of runaway electrons. The fully commissioned system became operationa…
-
UKAEA-CCFE-CP(23)392021
A key aim of the 2021 JET deuterium-tritium (D-T) experiments was to demonstrate steady high fusion power (10-15MW) with the ITER-like Be/W first wall. Plasmas were developed using D, repeated with T to investigate and mitigate isotope effects, and run with D-T to maximise fusion power. Compared with high current (q95~3) ‘baseline’ plasmas, …
Showing 1 - 10 of 30 UKAEA Paper Results